GridStor® (Alternate Data Paths) - Best Practices
Avoid Data Fragmentation by Using Fewer Storage Policies
Create and use fewer storage policies, because having a large number of storage policies contributes to the fragmentation of data on media. Consider these options:
- Control data retention by creating copies within the Storage Policies (rather than creating many storage policies with different retention periods.)
- Consolidate each client computer's data by creating a storage policy copy by associating the subclient in the Association tab. See Assigning CommCell Entities to a Storage Policy Copy for instructions.
Deconfiguring a Library
Before you deconfigure a library, verify and ensure that none of the Storage Policy Copy's default data path points to the library. (See View the Storage Policies Accessing a Library for step-by-step instructions on how to view the storage policies associated with a library.) If necessary, set an alternate data path as the default data path before deconfiguring the library.
If you have a storage policy copy with no default data path, use Change Data Path option to migrate the storage policy to point to another data path. See Change Data Path for more information.
NAS Load-Balancing - in addition to the resource load balancing that the Alternate Data Paths feature provides, NAS can be configured to load balance the processing tasks associated with backup, restore, and auxiliary copy jobs, which normally run on a single client machine, to spread the processing among different MediaAgent.
Data paths for NAS attached libraries can only be added if the MediaAgent used in that data path also has the File System iDataAgent installed on that computer.
Using Alternate Data Path to Backup the Microsoft Virtual Server
If the MediaAgent software is installed in the cluster server, configure a disk library to backup the data.
If you want to configure a tape library, install the MediaAgent software on the physical computer.
Add a data path which uses this MediaAgent, Library, Drive Pool and Scratch Pool combination to the Storage Policy used to backup the cluster server. (See Add a Data Path to a Storage Policy Copy for more information.)
Assign this as a high priority data path in the subclients used to backup the cluster server. (See Assign Priorities for Subclient Data Paths for more information.)
Checking Media Compatibility While Changing Data Paths in Libraries and Drives
When you change the data paths make sure that the libraries and drives in the source and destination library are compatible. Specifically, the destination library must be capable of reading the bar codes on the media for which you have changed the data path. See the library manufacturer's documentation for compatible bar codes.
Make sure that the firmware of the source and target library can read the barcodes of media exactly the same way.
Ensuring Compatibility and Availability of Drive Pools
Ensure that the drives of the destination drive pool are compatible with the recording format and hardware type of the migrating media.
- An example of recording format incompatibility: Data paths can be changed from DLT 4000 drives to DLT 7000 drives as tapes written by DLT 4000 drives can be read in DLT 7000 drives. However, data paths cannot be changed from DLT 7000 drives to DLT 4000 drives, as tapes written by DLT 7000 drives cannot be read in DLT 4000 drives.
- Another example of hardware type incompatibility: DLT tapes cannot be inserted into AIT or Mammoth drives or vice-versa.
- Media from an NDMP drive pool can only be changed to another NDMP drive pool. (An NDMP drive pool is one containing drives that are attached to a NAS filer rather than to a MediaAgent.) Data Paths cannot be changed from NDMP to non-NDMP libraries.
Also confirm that there are sufficient drives in the destination drive pool to accommodate all of the streams of the copy for which the data paths are changed. For example, a drive pool should contain at least three drives to accommodate a three-stream copy.
Changing Data Paths in Compatible Libraries and Drives
It is possible to change the data paths for compatible libraries to stand-alone libraries and vice-versa, and between compatible stand-alone drives to stand-alone drives.
Exporting Media When Changing Data Paths Between Libraries
When you change the data paths from one library to another, you must physically remove all of the media from the source library and insert them into the destination library. It is strongly recommended that you export such media from the source library and immediately import them in the target library. If you want to export all the media from the library, you can use the Mark Media Exported option from the library level. For more information, see Export Media.
Once you change the data path and import the media in the target library, subsequent backup operation, which uses these media, will mark active media as appendable and use a new media.
Configuring Alternate Data Paths for Existing Libraries
When multiple MediaAgents share the same library (SAN DDS, or direct-attached shared library configurations) the system can automatically add the alternate data paths for each of the storage policies, when this option is enabled. As each of these data paths (MediaAgent, Library, Drive Pool and Scratch Pool) use the same resources, additional index cache configuration is not required. In addition, the criteria for using the alternate data path (described in the following section) must also be specified.
Using Alternate Data Path for a Shared Library Configuration
If both the default and alternate data paths are configured to use the same library, as a result of a shared library configuration (configured as a SAN DDS library or direct-attached shared library) the MediaAgent will automatically use the appropriate Assigned media for the data protection operation.
If the default and alternate data paths are configured to use different libraries, the MediaAgent, marks the previously used Assigned media as Appendable and uses a new media from the library associated with the alternate data path.
Such Appendable media can be re-used in the library by enabling the Use Appendable Media option in the Library Properties dialog box associated with the library.
MediaAgent Service Pack and Software Version Must be Same
In a GridStor configuration, all MediaAgents must be of the same service pack of the software version.
Last modified: 6/12/2019 3:11:10 PM