> Expert > Commvault HyperScale > HyperScale X > Maintenance > Expanding the Storage Pool

Prerequisites for Adding Nodes to an Existing HyperScale X Storage Pool

The following prerequisites are required to add additional nodes:

Existing Node Requirements

Review the following requirements to add an existing node:

  • Check the following minimum required versions in your existing setup and make sure to upgrade the versions where needed.

    • CommServe Server Version

      View the CommServe server version to ensure that Commvault Platform Release 2023E (11.32.35) or higher is available.

      If the CommServe server is in an earlier version, update the software to the latest maintenance release version as described in Updating Commvault Software on a Server.

    • HyperScale X MediaAgents Version

      View the version for the HyperScale X MediaAgents associated with the storage pool in which you plan to add the new nodes to make sure that Commvault Platform Release 2023E (11.32.35) or higher is available.

      Verify and ensure that all the MediaAgents in the storage pool have the same software version.

      If one or more MediaAgent is in an earlier version, update the software to the latest maintenance release version as described in Updating Commvault Software on a Server.

    • HyperScale X Platform Version

      View the HyperScale X platform version in the existing nodes to make sure that HyperScale X Platform Version 2.2312 (or higher) is available.

      For HyperScale X clusters that was installed using the Hyperscale ISO 3.2312 image, make sure that HyperScale X Platform Version 3.2312 (or higher) version is available.

      If one or more nodes is in an earlier version, install the OS updates as described in Installing Operating System Updates on Existing Nodes.

      Verify and ensure that all the nodes in the storage pool have the same platform version.

    If the above requirements are met, you do not require to download and install software and platform version updates to add additional nodes.

  • Enable root access, if root access is disabled in the storage pool. For more information, see Enabling or Disabling Root Access.

    Note

    Do not change the default root password on the node. (You will be prompted for a new password, during the Add Node operation.)

New Node Requirements

Consider the following before adding new nodes:

  • New nodes must be identical to the existing nodes in the storage pool, with the same drive count and drive size.

    • Mixing of certified hardware vendors or server generations is supported provided the same drive count and drive size is maintained.

    • If the same size drive cannot be used, larger drives may be used, however, they will be formatted to match the existing drive size, resulting in some loss of native capacity.

    • Mixing of Appliance nodes and Reference Architecture nodes is not supported.

  • Adding a HSX 3.x node to an existing 2.x cluster is supported.

    • Commserve will need to be at Commvault Platform Release 2023E or higher.

    • Prior to adding the node(s), the existing 2.x cluster must be on platform version 2.2312 or higher.

    • It is not required to upgrade the existing nodes to 3.x immediately after the new node is added.

    • Clusters running in mixed HSX 2.x and 3.x platform versions are supported.

    • You must upgrade 2.x nodes to 3.x version at some point prior to June 30th, 2025.

    Mixing of Appliance nodes and Reference Architecture nodes in the same storage pool is not supported.

  • A maximum of 12 nodes can be added to an existing storage pool.

    See also: Sizing Guidelines and Capacity Planning

New Node Setup

Setup the hardware in the new nodes using the following information:

  • Racking the Hardware

    Rack the new HyperScale X Appliance nodes to properly mount and secure the hardware.

    For more information, see Racking the Hardware.

  • Determine the network configuration in your existing setup

    You must setup the new nodes using the same topology that was originally used in your existing setup. Check your existing network configuration to understand the network topology used in the existing nodes.

    For more information about the supported topologies, see Determining the Network Topology

  • Setup the DNS

    Setup the necessary DNS records for the new nodes.

    For more information, see Setting Up the DNS.

  • Setup the Switches

    Ensure that the switch configurations are in place depending on the network topology in your environment.

    For more information, see Setting Up the Switches.

  • Setup the IPMI

    Power on the new nodes and setup the Intelligent Platform Management Interface (IPMI) port.

    For more information, see Setting up a Static IP For Intelligent Platform Management Interface.

  • Verify HyperScale X Image Version

    Check the HyperScale X image version on the new node to ensure that the image version is Hyperscale ISO 3.2312.

    If the image in the node is in an earlier version, you can re-image the new nodes with the most recent version, and then add the new nodes.

    For more information, see Re-Imaging Commvault HyperScale X .

  • Obtain the CommServe server credentials

    Obtain the necessary credentials to connect to existing CommServe server.

    For more information, see Connecting to an Existing CommServe Server.

Loading...