Loading...

Guidelines for Adding Subclient Content

Review the following guidelines before defining subclient content.

Guidelines

  • Regular expressions can be used to select volumes for the subclient.
  • Wildcards cannot be used to select subdirectories within the volumes.

    For example, for vendors with volumes that are preceded by /vol, adding /vol/[A-L]* will backup all volumes that start with the letters A through L. For vendors with volumes that are not preceded by /vol/, adding /[A-L]* will backup all volumes that start with the letters A through L. Subclient content with regular expressions that are not volume paths will be treated as non-regular expressions. For detailed information about using wildcards to define subclient content, see Supported Wildcards for NDMP.

  • Subclient content is case-sensitive.

Content Format and Browse Support

The following table contains some examples of the subclient content format for some (but not all) supported NAS vendors.

Vendor

Details

Subclient Content Format

Example Subclient Content

Browse for Subclient Content

Hitachi

No root volumes are shown in the drop down list. Type the full path of the root volume.

/mount_point/ volume_name

/mnt/FS1

Supported

Hitachi NAS (BlueArc)

The root volume is a combination of a descriptor of the path and the volume name.

/__VOLUME__/file system name/path in the file system

/__VOLUME__/FS1/dir1

/__VOLUME__/FS1

/__VOLUME__/[A-L]*

/__VOLUME__/FS?

Supported

Note: Because the Hitachi NAS (BlueArc) filer does not have an NDMP browse extension, you must add the Hitachi NAS (BlueArc) file server to Array Management using credentials with the proper permissions.

For information about adding the Hitachi NAS (BlueArc) file server to Array Management, see Configuring Hitachi NAS Using Array Management.

Huawei

To obtain the corresponding file system ID for a particular file system name, in the Huawei OceanStor DeviceManager, go to File System properties.

/file system ID/path in file system

/filesystem0/dir1

/filesystem2/dir2/data

/filesystem*

Not supported

Dell EMC VNX / Celerra/VNXe/Unity/PowerStore

The root volume is the mount point created for a volume.

For Celerra tape silvering, specify the source path of the replication that was created from the Celerra Management Console or command line. Append .ts to the path name.

/Virtual Data Mover/File System Name/path in file system

/dept1_vdm1/filesys_2018_team1

/dept1_vdm1/filesys_2018_team1/subdir

/dept1_vdm*/filesys_2018*

/filesys_dept*

/sourcefs/.ts

Not supported

Dell EMC Isilon/PowerScale

 

/ifs/path in the file system

/ifs/dir1

/ifs/dir2/data

Supported

Note: Because the Dell EMC Isilon/PowerScale filer does not have an NDMP browse extension, you must add the Dell EMC Isilon/PowerScale file server to Array Management using credentials with the proper permissions.

For information about adding the Dell EMC Isilon/PowerScale file server to Array Management, see Configuring Dell EMC Isilon/PowerScale Using Array Management.

NetApp 7-Mode

The root volume is the mount path of each volume.

/vol/volume_name

/vol/vol0

/vol/vol1/datadir

/vol/[A-L]*

Supported

NetApp Cluster Mode (C-Mode)

 

/Vserver_name/volume_name

/dept1_vserver1/volume1

/dept1_vserver2/volume1/data

/dept1*/volume*

Supported

Note: To browse for subclient content on NetApp C-Mode file servers, you must do one of the following:

Oracle ZFS

The format for the subclient content depends on the type of backup operation.

To perform a block backup, the subclient content path must be the Oracle ZFS Storage Appliance ZFS path to the project, share, or LUN. For detailed information about the formats to use, go to the Oracle document NDMP Implementation Guide for the Oracle ZFS Storage Appliance, NDMP Formats.

/export/volume_name

Block backups:

/pool/local/project

/export/Volume*

Block backups:

/pool001/local/project*

Not supported

Last modified: 8/26/2020 8:49:35 PM