Auxiliary Copy Job Options
Use this dialog box to select the criteria to perform an Auxiliary Copy operation.
Select a Storage Policy
Allows you to select the storage policy from which you will run an auxiliary copy operation. (Applicable for the CommServe level only. This field will not display storage policies that do not have secondary copies configured.)
Select Source MediaAgent
Allows you to select the source MediaAgent from which you will run the auxiliary copy. (Applicable for copies that are configured with a shared library only.)
If a source copy used for the Auxiliary Copy job is configured with a shared library, you can select a MediaAgent to read the data during the Auxiliary Copy operation.
When the <Any MediaAgent> is selected, the system automatically picks up the appropriate MediaAgent, especially when multiple MediaAgents are associated with the copy. This improves the auxiliary copy performance.
- All Copies
If selected, data from the source copy will be copied to all active secondary copies. If cleared, the Select a Copy field is enabled and you must select an secondary copy from the drop down list of active secondary copies.
- Select a Copy
If selected, data from the source copy is copied to the secondary copy you select from the drop down list of active secondary copies. If cleared, the All Copies field is enabled, and data is copied from the source copy to all active secondary copies.
Number of Readers
Allows you to select the data streams that are copied at the same time during the auxiliary copy operation.
- Number of Streams
Allows you to select the number of data streams that are copied at the same time during the auxiliary copy operation.
- Allow Maximum
If selected, the maximum number of data streams will be copied at the same time during the auxiliary copy operation.
Start new media
If selected, the option causes the following to occur:
- If removable media (tape) is being used on a secondary copy, the current active media is marked as full and a new media is used for the auxiliary copy.
- If disk media is used, a new volume folder is created for the auxiliary copy.
If cleared, the auxiliary copy automatically uses the current active media or volume.
Mark media full On Success
If selected, the media used for the auxiliary copy operation is marked full after the operation is successfully completed.
Use Most Recent Full Backup For Auxcopy
If enabled, the most recent successful full backup for each subclient will be copied to selective copies when an Auxiliary Copy job is run.
If disabled, only the previously selected full backup jobs or manually selected jobs will be copied to selective copy when an Auxiliary Copy job is run.
Note: This option is applicable only for Selective Copies when Do not Automatically select jobs option is enabled on the Selective Copy tab of the selective Copy Properties dialog box.
When enabled during Auxiliary Copy operation the following jobs are copied:
- The most recent full backup for all subclients associated with the storage policy.
- The partial jobs available on the selective copy.
- The jobs that are manually selected for copy.
Wait For All Parallel Copy Resources
If selected, the auxiliary copy operation will not start for parallel copies until all resources (MediaAgents and libraries) for the parallel copy are available.
Use Scalable Resource Allocation
If selected, the scalability of the auxiliary copy operation is enhanced and the CommServe resources are optimally utilized. For example, all the device streams are effectively utilized and there is load balancing across all MediaAgents in case LAN-free MediaAgents are not available.
Note: The CommServe resources will not be optimally utilized during the auxiliary copy operations in the following conditions:
- When running the auxiliary copy operation for NAS data
- When the MediaAgents are not upgraded to the latest Commvault version
Skip jobs that failed data verification
If selected, the backup jobs that did not complete the data verification operation with a successful status will not be copied during the auxiliary copy operation.
Save As Script
Click to open the Save As Script dialog, which allows you to save this operation and the selected options as a script file (in XML format). The script can later be executed from the Command Line Interface using qoperation execute command.
When you save an operation as a script, each option in the dialog will have a corresponding XML parameter in the script file. When executing the script, you can modify the value for any of these XML parameters as per need.
Auxiliary Copy Schedule
Use this dialog box to select a schedule type for an auxiliary copy operation of this copy.
Associate to Schedule Policy
Click to enable the Automatic Copy operations. If selected, the auxiliary copy will select the system default and will automatically copy data from the primary copy to this copy at 30-minute intervals. This interval can be changed in the Auxiliary Copy Job Initiation dialog box.
You can also select any other schedule policy to run auxiliary copy operation as per your specific requirement from the available dropdown list.
Click to define a custom schedule. Provides access to the Auxiliary Copy dialog box, which allows you to select options for the auxiliary copy operation, and to schedule the operation or choose to run an auxiliary copy operation immediately.
Do Not Schedule
Click if you do not wish to schedule an auxiliary copy operation for this copy at this time.
Auxiliary Copy Advanced - Scalable Resource Allocation Online Help
On upgrading to the latest service pack, this option is selected by default. You can specify the number backup jobs that have to be processed during the auxiliary copy operation. For example, if 100 jobs are specified, and there are 1000 jobs that needs to be copied, then the auxiliary copy job will process 10 batches of 100 jobs each.
Total jobs to process
If you have upgraded to the latest service pack, then by default 1000 jobs are processed. Use the arrows to select a desired number of jobs.
Process jobs between
Select this check box to specify a specific date and time range, and the number of jobs specified for the Total jobs to process option, will be processed during the auxiliary copy operation.
Specify the scheduled start date and time for the setting the time range.
Specify the scheduled end date and time for the setting the time range.
To run auxiliary copy operation after the jobs in the current time frame are copied, you must create a new schedule or edit the time frame of the existing schedule.
Last modified: 3/1/2018 4:23:00 PM