VM Conversion Using Commvault Hotadd

HotAdd Restores

HotAdd restores for Amazon provide faster performance than traditional restores. By using an access node (VSA proxy) that is running on an Amazon instance, the restore operation can write directly to Elastic Block Storage (EBS) and inject Amazon drivers that are required for destination instances.

HotAdd restores are used for the following operations:

Restores
Live sync operations
Conversion from VMware to Amazon, for the following VMware guest operating systems:
- Microsoft Windows Server 2019 (Standard, Datacenter) (64-bit only)
- Windows Server 2016
- Windows Server 2012 R2
- Windows Server 2008 R2
  
  Note
  
  For VM conversion or live sync replication of guest VMs that run Windows Server 2008 R2 and later versions, validation might fail for the converted instance in AWS. To resolve this issue, set the RealTimeIsUniversal registry key on the source VM as described in the AWS article Configuring Time Settings for Windows Server 2008 and later, and then perform a new backup to use as the source for the conversion or replication.
- CentOS 7.x
- RHEL 6.x
- RHEL 7.x
- Ubuntu 18.x

Requirements for HotAdd Restores

The Virtual Server Agent proxy selected for the operation must be an Amazon instance in the same zone as the destination instance.

Note

For cross-hypervisor restores or replication from VMware to Amazon, you can use a VSA access node that runs on Windows or Linux. If you use a VSA access node that runs on Linux, for both Windows and Linux guest VMs, the drivers must be installed on the source before performing the backup. Otherwise, the replication operation fails. You cannot use a Linux proxy for the import method.

Requirements for VM Conversion and Live Sync Replication Operations when Amazon is the Destination

For Windows guest VMs, you can copy drivers that are required for AWS instances to the access node (VSA proxy) that is used for conversion or replication operations. During the conversion or replication operation, drivers are automatically installed on the destination guest instances.

For Linux guest VMs, you must copy the required drivers to the source VMs and then perform a new backup to use as the source for conversion or replication operations.

For Windows VMs: Commvault attempts to copy required drivers automatically for conversion or replication to AWS instances, but automatic downloads might fail if a firewall is in place. If that occurs, you can copy required drivers to the access node that is used for the operation, and then retry the operation.

On the VSA proxy, create an Amazon folder under the software_install_path/Commvault/ContentStore folder, and extract the contents of the following zip files in the Amazon folder:
- https://s3.amazonaws.com/ec2-downloads-windows/Drivers/AWSPVDriverSetup.zip
- https://s3.amazonaws.com/ec2-downloads-windows/EC2Config/EC2Install.zip
Extract the following files to separate subfolders under the Amazon folder:
- https://s3.amazonaws.com/ec2-windows-drivers-downloads/NVMe/Latest/AWSNVMe.zip
- https://s3.amazonaws.com/ec2-windows-drivers-downloads/ENA/Latest/AwsEnaNetworkDriver.zip
Make the following changes to source VMs before performing the backup that is used for conversions:
- When performing conversion or replication for an Active Directory domain controller, upgrade PV drivers as described in Upgrade a Domain Controller (AWS PV Upgrade).
- Windows source VMs:
  - Install .NET 4.5 or a more recent version of .NET.
  - Enable Remote Desktop Protocol (RDP).
  - Disable Windows Firewall.
  - Disable User Account Control (UAC) in the Windows Control Panel.
  - Ensure that there is a minimum of 2 GB free space on the C: drive.
  - Verify that the Windows AutoAdminLogon feature is not disabled on the source VM, so that AWS drivers can be installed on the destination VM during conversion.
  - HotAdd conversion is not supported if the boot OS for the source VM uses GUID Partition Table (GPT) partitioning. Use the import method instead.
  - If the Windows security banner is enabled on the source VM, install the following components so that the converted instances can pass instance status checks:
    
    https://s3.amazonaws.com/ec2-downloads-windows/Drivers/AWSPVDriverSetup.zip
    
    https://s3.amazonaws.com/ec2-downloads-windows/EC2Config/EC2Install.zip
  - To replicate source VMs that run on a version of Windows Server earlier than Windows Server 2012 R2, when the Windows AutoAdminLogon feature is disabled or when a firewall is in place in the environment, install drivers on source VMs before performing the backup that is used for replication, as described in Installing Drivers Manually for HotAdd Replication.
- Linux source VMs:
  - Enable Secure Shell (SSH) for remote access.
  - The host firewall (such as Linux iptables) must permit access to SSH.
  - Ensure that Xen drivers are installed on the VM:
    
    xen-blkfront
    
    xen-netfront
    
    Installing Xen drivers on Linux guest VMs before backing up the VMs enables the required drivers to be in place when the Amazon instances are created, so that the Amazon instance can be started and users can access the instance.
  - To enable restores to Nitro instances, install NVMe and ENA drivers on source VMs or instances as described in the following pages (depending on the operating systems for the source VMs or instances):
    
    Amazon EBS and NVMe on Linux Instances
    
    How do I install and enable the latest ENA driver for Enhanced Network Support on an Amazon EC2 instance running Red Hat 6/7?
  - Ensure that Linux VMs use GRUB (GRUB legacy) or GRUB 2 as the bootloader.
  - Linux VMs must use one of the following for the root file system: ext2, ext3, ext4, Btrfs, JFS, or XFS.
  - Linux VM /etc/fstab entries should use UUIDs instead of device names, because device names might change on conversion.

HotAdd Restore Process

Windows:

Create empty EBS volumes.
Attach EBS volumes to proxy.

Up to 21 volumes can be attached to the VSA proxy during cross-hypervisor restores or live sync replication, occupying device slots xvdf - xvdz.
Restore data to EBS volumes.
Inject AWS components and drivers.
Detach volumes from the VSA proxy.
Create the Amazon instance from the EBS volumes.
Automatically log on to the instance to install PV drivers and EC2 configuration service.

Linux:

Create empty EBS volumes.

Up to 21 volumes can be attached to the VSA proxy during cross-hypervisor restores or live sync replication, occupying device slots xvdf - xvdz.
Attach EBS volumes to proxy.
Restore data to EBS volumes.
Detach volumes from the VSA proxy.
Create the Amazon instance from the EBS volumes.